24 Channels led lamp rgb DMX Controller

DMX Controller,rgb dmx controller a.db-DMXTCON-24CH b.12V/24V DMX controller c.3/4/24 channels d.led lamp rgb DMX controller

DMX Controller,rgb led lamp DMX Controller

The decoder adopt the advanced micro-computer control technology and converted the DMX512 digitalsignal widely used in international to the analog control signal. 1~24 channels output for option and eachchannel able to achieve 256 gradations of controlling, and also it can be used as the connector of PC digitallight controller and analog light modulator. It is mainly used for the controlling of buildings & lights applied LED.

(1) DMX Signal input interface RJ45(2) DMX Signal output interface RJ45(3) Address setting interface(4) Drive output interface

(5) Power input interface(6) XLR 3 input male-end(7) XLR 3 output female-endDMX Signal interface:

Address code setting on/off:Please see the operating instruction next page.Power input interface:DC12~25V input,supplied power with the decoder and the lamps it takes.Drive output interface:Common in anode-V+ and with 8pcs of V+ interface & 24pcs of R, G, B output interface. Not only does it applyto the various of LED module in full-color & mono color, but also it can self-trimming the output current based onthe load of LED module.Remark:Connect the anode and RGB wire of common anode RGB module to the output interface of decoder directly;Connect the anode wire of single-color module to V+ on decoder, and connect the cathode wire to one of RGBpin according to the LED's color; Connect several colors single-color module to one decoder, please connecttheir anode wires to V+ pin on decoder.Direction for use1. Connecting of DMX-512 Signal Cable:DMX signal cable used the CAT-5 cable,and DMX signal tells positive(+) from negative (-). While weldingthe DMX signal cable plug, there must pay much attention to know positive (+) from negative (-), and thenconnect the DMX512 signal cable with the corresponding input interface of DMX512 decoder correctly.2. DMX-512 address code set:DIP switch of DMX512 decoder is with the function of writting the binary system and reading the DMX512address code. DMX512 decoder is a decoder with 24 channels, When it is on-line job, the second DMX512decoder should be set the address code as the 25th channel. The 10th bit is TERM and will be the terminalwhile it is off.(Only used for the signals circuit setting).The bits from1 to 9 of DIP switch are as the key ofwriting DMX address code, 1 is LSB and 9 is MSB; total 512 address codes. The initial address code is the DMX signal received by the No.1 channel of decoder, Calculational formula:[ Sum of 1~9 bits of DIP switch ] =DMX initial address code Set the n(th) bit of DIP switch up(set to“1”)to get the value of such bit; Set the n(th)bit of the DIP switch down “0”),so the value of this bit is 0.

Example 1:Set to 38Set the 6th,3rd,1st bit of the DIP switch to“1”,others set to“0”,then the sum of 1~9 is 32+4+2,is the startaddress 38.That is:[ 32 + 4 + 2 ] = 38

Example 2:Set to 226Set the 8th,7th,6th,1st bit to “1”,others set to“0”,then the sum of the 1~9 is 128+64+32+2,is the startaddress 226.

3. Points for attention in installing and usingPrinciple in installing & using:(1) The input voltage should be limited in rated range.(2) Do not use it by over load.(3) Installed in suited environment.A. The driver can not be setting in high temperature or wet conditionsB. We recommend three ways to take away the heat as followsBared in moving airPut in a big enough space for taking away the heatFixed on big metalline board, and make sure they are contacted wellPoints for attention in installing and using:(1) The reliable length of the line is 200m, please try to put the controller close to the decoder so as toavoid the signal become weak in using with the controller.

(2) Recommend to use the STP with the characteristic impedance of 120Ω(3) It is better to use one bus for the signal line, and join up with the in/out splice of the decoder.(4) Make sure to fix the signal line to the splice of decoder(5) Please try to keep the decoder close to the light, if the light is over 5m, it is better to re-connect thelight and decoder.(6) If there are several lights connected in series, please make sure the splice is firm and impervious joint.(7) Signal line should be far away with the 110/220V AC cable

trade Terms1.Payment: T/T to be paid before delivering  (Western Union is welcomed)2.Production lead time  for 100~500rolls: 10days, 500~1000rolls:15days3.Sample can be delivered in 3days4.Shipping freight are quoted under your requests5.Shipping port: Shenzhen, Mainland China6.Discounts are offered based on order quantities7.MOQ:10rolls

our service1.Your inquiry related to our products or prices will be replied in 24hrs.2. Well-trained and experienced staffs to answer all your enquires in fluent English3.OEM&ODM, any your customized lightings we can help you to design and put into product.4. Distributoership are offered for your unique design and some our current models5.Protection of your sales area, ideas of design and all your private information

About DBLIGHTS all customers (news and formals)

DBLIGHTS objective is to be your long-term strategic partner, to help you optimize your profitability, and to provide you with stylish products of first-rate workmanship at highly competitive prices - with prompt and reliable service. 

To us, the customer always comes first.Know more about led bulb detail,please visit our website: www.dblights.com www.dblights.en.alibaba.com

24 Channels led lamp rgb DMX Controller